65TH IASTEM INTERNATIONAL CONFERENCE
Los Angeles, USA 20-07-2017
8 papers
-
Simulation Of Landfill Gas Production Rate And Methane Concentration: Modelling And Verification Through Field Measurements
I. Palogos, I. Chourdakis, K. Tsafantakis, P. Gikas
Paper ID IA-ICENSLOSANGL-20077-4603 · Pages 1-4
Download PDF: Simulation Of Landfill Gas Production Rate And Methane Concentration: Modelling And Verification Through Field MeasurementsAbstract
Landfill Gas (LFG) is mainly consists on methane () and carbon dioxide (CO2). CH4 concentrations is important for the estimation of the potential for electric energy production form LFG. Most of the models used to estimate the LFG production rate and CH4 the content of LFG do not take into account the reduction of concentration with time, as a result of air diffusion into the landfill, especially during the last phase of methanogenesis and during maturation phase of landfilling. The present study proposes modifications to the EPA’s Landgem model for the simulation of the aforementioned parameters. Onsite measurements in Fodele landfill, Heraklion, Greece indicated that the model simulation results are close the measured values. Thus the modified Landgem model may be used to estimate the potential for electric energy production from landfills. Keywords - landfill, biogas, Waste to Energy, Landgem, LFG, methane
-
Method For Controlling The Circular Type Micro Hole Size On Stainless Steel Thin Film By Photoresist Etching
Xiong-Jie Cui, Seong-Hyun Kim, Seung-Geon Choi, Eun-Sang Lee
Paper ID IA-ICMAELOSANGL-20077-4180 · Pages 5-8
Download PDF: Method For Controlling The Circular Type Micro Hole Size On Stainless Steel Thin Film By Photoresist EtchingAbstract
Fast development of wafer level packing (WLP) in recent years is mainly owing to the advances in integrated circuit fabrication process and the market demands for devices with high electrical performance, small form factor, low cost etc. Evaporating and electroplating are the two wafer solder bump processes in production today. Evaporating is high cost, and can not produce eutectic solder bumps due to the Sn and Pb vapor pressure difference. Electroplating is a relatively low cost option, but it requires photoresists steps that add to the cost and plated bump composition is not easy to control due to differences in Sn and Pb electrochemical behavior. Stencil print technology is a well established process used in surface mount board assembly. Technology advances in solder paste, stencil fabrication, and printing equipment make it possible to print Sn/Pb solder paste onto wafer to form bumps. Nowadays, there are three types of stencils available, chemical etching, laser cut and electroformed. Chemical etch stencils are cheap, but has the dimension and accuracy limitation. In this study, for improving the dimension and accuracy of stencil hole size, the etching conditions and methods for controlling the circular type micro hole size on 50µm thickness stainless steel has been investigated. For controlling the machined hole size with etching method, the relationship between dry film photoresist coating size after exposure and development and machined hole size has been compared. And also, the hole size machining limitation of etching method has been confirmed. Keywords - Stencil Printing, Stencil Mask, Stainless Steel Thin Film, Etching
-
A Study On Machining Characteristics For Composition 3-Dimensional Shape Using Pulse Electrochemical Machining: Optical Microscopic, Non-Contact 3d Measurement Study Of Surface Analyses
Seong-Hyun Kim, Seung-Geon Choi, Xiongjie Cui, Eun-Sang Lee
Paper ID IA-ICMAELOSANGL-20077-4386 · Pages 9-12
Download PDF: A Study On Machining Characteristics For Composition 3-Dimensional Shape Using Pulse Electrochemical Machining: Optical Microscopic, Non-Contact 3d Measurement Study Of Surface AnalysesAbstract
As the level of precision increases gradually in the area of processing technology, interests in precise and complicated image processing increase as well particularly in the area of MEMS-related micro machinery and processing method development. However, technologies develop complementarily. While researches on processing technology for 3D micro structures are conducted actively, processing aspects involve problems. For instance, 3D image processing involves the remaining deformation layer after micro electric-discharge machining. Micro electro-chemical machining itself is superior in terms of surface roughness improvement, but its form accuracy is not as great as that of micro electric-discharge machining. The present study aims to examine the relevance between pulse electro-chemical machining variables and the processing state and to verify the potential of micro-precision image processing by measuring and inspecting the surface condition and image of electro-chemically machined specimens. Index Terms - 3-Dimensional shape, Pulse electrochemical machining, Machining depth, applied voltage,
-
A Study On Electrochemical Machining Performance Analysis Of Shape Memory Alloy With Electrolyte And Electrode
Seung-Geon Choi, Seong-Hyun Kim, Xiong-Jie Cui, Eun-Sang Lee
Paper ID IA-ICMAELOSANGL-20077-4512 · Pages 13-17
Download PDF: A Study On Electrochemical Machining Performance Analysis Of Shape Memory Alloy With Electrolyte And ElectrodeAbstract
Nitinol shape memory alloy (SMA) is used in various industries such as medicine and aerospace. Micro-scale and complex shapes of SMA are often needed. Electrochemical machining is a non-contact method that has advantages regarding defects like thermal strain and micro burrs compared to other non-conventional machining methods, such as laser machining, electro-discharge machining, and etching. An insulated electrode is required for precise electrochemical machining. In this study, current density analysis was performed to determine the current density for three types of electrodes. The isolated electrodes had high current density in the same conditions. The workpiece was nitinol SMA. Square shapes were fabricated in electrochemical machining using a square electrode, a square electrode insulated on only the sides, and a square electrode insulated on the sides and center. The influence of the insulation layer on the applied current has been investigated. It is possible to obtain precise square shapes on SMA if the insulation layer controls the unnecessary current between the electrode and workpiece, which would be helpful in the medical and aerospace industries. The square electrode without an insulation layer creates inexact square shapes due to the unnecessary current. The side-insulated electrode creates precise square shapes. The most precise square shapes were found when the square electrode insulated on the sides and center was applied because the insulation layer concentrates the unnecessary current on the machining area and improves the removal rate. Index Terms - Shape memory alloy (SMA), Micro machining shape, General electrode, Fillet electrode
-
Dynamic Business Environment And Development Of Entrepreneurial Skills With The Use Of The Bistro Simulation
Alina M. Zapalska, Nicholas Zieser
Paper ID IA-ICSSHLOSANGL-20077-3759 · Pages 18-23
Download PDF: Dynamic Business Environment And Development Of Entrepreneurial Skills With The Use Of The Bistro SimulationAbstract
The paper describes a simulation that represents an active teaching tool which allows players to develop and practice entrepreneurial skills. The simulation allows students to discover, identify, develop, practice, and test entrepreneurial skills in a variety of market contexts. Students learn that the entrepreneur appears to have special personal qualities among which include: internal locus of control, risk-taking, innovation and initiative, ability to solve immediate problems, desire for responsibility and success, need for achievement and control, growth-orientation, power, and aggression. Students' experience with the simulation develops appreciation of entrepreneurship as a leading factor for economic growth and development in globally integrated international markets. Index Terms - auction, asset allocation, business game, entrepreneurial success, strategic decisions, tactical decisions.
-
Assessing Paid Mobile Learning App Success
Hsin-Hui Lin, Yi-Shun Wang, Yu-Yin Wang, Tung-Han Tsai
Paper ID IS-CABMISCHICGO-25077-4018 · Pages 24-27
Download PDF: Assessing Paid Mobile Learning App SuccessAbstract
Increasing mobile device market penetration across the globe and growing demand for digital education are visibly driving the market for mobile learning (m-learning). Facing increased competition, paid m-learning applications (apps) are much less likely succeed in the app marketplace than free ones. Therefore, understanding how to assess the success of paid m-learning apps has become an important issue for academics and practitioners. Based on the information systems (IS) success models and the value-based adoption model, this study proposed a multidimensional model for assessing paid m-learning app success. The proposed model describes the interrelationships among seven paid m-learning app success variables: System Quality, Information Quality, Perceived Enjoyment, Perceived Fee, User Satisfaction, Intention to Reuse, and Learning Effectiveness. Keywords - Paid mobile learning apps, information system success model, value-based adoption model, intention to reuse, learning effectiveness.
-
Electoral Behavior And Socio-Economic Status In Iran: An Empirical Study In Shiraz City
Laleh(T.S) Hashemi
Paper ID IS-CESSUSA-22077- 3599 · Pages 28-32
Download PDF: Electoral Behavior And Socio-Economic Status In Iran: An Empirical Study In Shiraz CityAbstract
The purpose of this study is to investigate the relationship between socio-economic status and its different attitudes that could influence voting behavior and political participation of individuals. This study posits that when the level of income, education and occupation (three main measures of socio-economic status) increase, there would be a decrease in the level of political participation.The questionnaire used to gather data in this study comprises two major sections namely: socio-economic status and political attitudes and participation in Shiraz, one of the most important cities in Iran. Keywords - Socio Economic status, voting behavior in Shiraz, presidential election, electoral participation, case study
-
Affective Design Of Functional Products For The Elderly
Kuo-Hsiang Chen, Ching-Chien Liang, Ya-Hsueh Lee, Po-Hsiang Peng, Jia-Xuan, Han
Paper ID IS-STEMCHICGO-25077-4496 · Pages 33-37
Download PDF: Affective Design Of Functional Products For The ElderlyAbstract
Based on the theory of charm engineering, this study adopts the methods and steps of user research and divides the whole process into three stages: (1) survey and categorization of functional household items for the elderly; (2) interview with the high involvement elderly regarding their affective preference; (3) questionnaire survey and statistical analysis of the representative functional household item for the elderly. Early results show that (1) in terms of product search ratio, mobility assisting and communication products have the highest proportion; (2) in terms of product sales ratio, mobility assisting products reaches 25% and footwear products are the highest among them; (3) interviews with high-involvement elderly show that footwear with 40.8% is the highest demand among functional household items. Therefore, footwear products will be used as example to conduct subsequent study on affective preference and affective design for the elderly. Index Terms - Affective design, Elderly, Functional products, Kansei engineering, High-involvement, Miryoku engineering.